AME 3rd SEM ASSIGNMENT 3RD

AME 3rd SEM ASSIGNMENT 3RD

Submit all assignment 1,2 and 3. Put assignments in a plastic file folder.
Date of Submission: 01-11-2012

      Q1.      Enumerate merits and demerits of front engine rear drive chassis layout.

      Q2.      State function of differential unit?

      Q3.      What is engine tuning?

      Q4.      Write short note on shock absorber?

      Q5.      How are wheels and tyres designated?

      Q6.      How automobiles are classified according to their body types?

      Q7.      Define “Toe in”?

      Q8.      Define “Toe out”?

      Q9.      Define camber?

    Q10.    Define caster?

    Q11.    Define kingpin inclination?

    Q12.    What is difference between constant mesh and sliding mesh?

    Q13.    Why wheel balancing is needed in an automobile?

    Q14.    Draw free hand sketch of hydraulic brake system?

    Q15.    Why suspension system is needed in an automobile?

    Q16.    What are different types of steering boxes?

    Q17.    Draw universal joint.

    Q18.    What are various types of rear axles?

    Q19.    What is dead axle?

    Q20.    What are various types of suspension?

    Q21.    What is independent suspension?

    Q22.    State Mc-pherson strut types suspension?

    Q23.    What is five link type suspensions?

    Q24.    What is double wishbone suspension?

    Q25.    What is pneumatic suspension?

    Q26.    Draw sketch of shock absorber.

    Q27.    State various types of wheels?

    Q28.    Differentiate between radial?

    Q29.    What is disc brake?

    Q30.    What is ABS?

 

ME 5TH B ASSIGNMENT 3RD

ME 5TH B ASSIGNMENT 3RD

Submit all assignment 1,2 and 3. Put assignments in a plastic file folder.
Date of Submission: 01-11-2012

Q1.What is a Dead Axle?

Q2.What is a Live Axle?

Q3.What is Camber?

Q4.What is Tie- Rod?

Q5.What is King Pin Inclined?

Q6.What is the function of a Braking System?

Q7.What is the basic principle of air braking system?

Q8.What are power Brakes?

Q9.What do you mean by Servo Brake?

Q10.                    What is a Cell?

Q11.                    What is a Battery?

Q12.                    How Many cells are there in a 12Volt battery?

Q13.                    What is capacity of a Battery?

Q14.                    What is an Electrolyte?

Q15.                    What is the source of electrical energy in Automobile?

Q16.  What is pre-ignition?

AME 3RD PRACTICAL NO. 10

AME 5TH SEM ASSIGNMENT 3RD

AME 5TH SEM ASSIGNMENT 3RD

Submit all assignment 1,2 and 3. Put assignments in a plastic file folder.
Date of Submission: 01-11-2012

Q1.      What is fundamental deviation?

Q2.      What is ductile material? Give its example.

Q3.      What is the effect of keyway and how this is taken care off in design of the shaft?

Q4.       Which of the theories of elastic failure is used in design of shafts and why?

Q5.       Write manufacturing methods of cotter and knuckle joint?

Q6.       What are applications of coarse and fine threads?

Q7.       What is caulking and fullering? Differentiate between the two?

Q8.       Sketch parallel and transverse welds?

Q9.       What do you understand by self-locking screw? Write its condition?

Q10.    Explain woodruff key? What are its applications?

Q11.    What is factor of safety?

Q12.    What is preloading of bolts?

Q13.    What is function of key? Sketch two types of keys

Q14.    What are design failure theories?

Q15.    What are different types of shaft?

Q16.    What is spindle?

Q17.    What is the function of cotter joint?

Q18.    Distinguish between knuckle and cotter joints?

Q19.    Muff coupling is also known as ______________ coupling. (Box)

Q20.    Two shafts are connected by ___________. (Coupling)

Q21.    ________ Coupling is used when two shafts are intersect at an angle. (Universal)

Q22.    The sleeve and muff coupling is designed as ____________. (Hollow Cylinder)

Q23.    Oldham coupling is used to connect two shafts are at __________. (Lateral misalignment)

Q24.    Flange coupling is the standard form of coupling hardly used in workshops to join two shafts by means of two _____________. (Flanges)

Q25.    Couplings are mainly divided into two categories ________ and _______. (Rigid, Flexible)

Q26.    In solid flange coupling _________ is not used. (Key)

Q27.    What is function of coupling?

Q28.    What is the difference between clutch and coupling?

Q29.    What are applications of flexible coupling?

Q30.   Define a bolt.

Submit all assignment 1,2 and 3. Put assignments in a plastic file folder.
Date of Submission: 01-11-2012