AME 5TH SYLABUS FOR 3RD MST
1. Weld
2. Rivet
3. Clutch
4. Frame
5. Brake
6. Steering
1. Weld
2. Rivet
3. Clutch
4. Frame
5. Brake
6. Steering
Tuesday, October 30, 2012
Sunday, October 28, 2012
Tuesday, October 16, 2012
AME 3rd SEM ASSIGNMENT 3RD
AME 3rd SEM ASSIGNMENT 3RD
Submit all assignment 1,2 and 3. Put assignments in a plastic file folder.
Date of Submission: 01-11-2012
Submit all assignment 1,2 and 3. Put assignments in a plastic file folder.
Date of Submission: 01-11-2012
Q1. Enumerate
merits and demerits of front engine rear drive chassis layout.
Q2. State
function of differential unit?
Q3. What
is engine tuning?
Q4. Write
short note on shock absorber?
Q5. How
are wheels and tyres designated?
Q6. How
automobiles are classified according to their body types?
Q7. Define
“Toe in”?
Q8. Define
“Toe out”?
Q9. Define
camber?
Q10. Define
caster?
Q11. Define
kingpin inclination?
Q12. What
is difference between constant mesh and sliding mesh?
Q13. Why
wheel balancing is needed in an automobile?
Q14. Draw
free hand sketch of hydraulic brake system?
Q15. Why
suspension system is needed in an automobile?
Q16. What
are different types of steering boxes?
Q17. Draw
universal joint.
Q18. What
are various types of rear axles?
Q19. What
is dead axle?
Q20. What
are various types of suspension?
Q21. What
is independent suspension?
Q22. State
Mc-pherson strut types suspension?
Q23. What
is five link type suspensions?
Q24. What
is double wishbone suspension?
Q25. What
is pneumatic suspension?
Q26. Draw
sketch of shock absorber.
Q27. State
various types of wheels?
Q28. Differentiate
between radial?
Q29. What
is disc brake?
Q30. What
is ABS?
ME 5TH B ASSIGNMENT 3RD
ME 5TH B ASSIGNMENT 3RD
Submit all assignment 1,2 and 3. Put assignments in a plastic file folder.
Date of Submission: 01-11-2012
Submit all assignment 1,2 and 3. Put assignments in a plastic file folder.
Date of Submission: 01-11-2012
Q1.What is a
Dead Axle?
Q2.What is a
Live Axle?
Q3.What is
Camber?
Q4.What is
Tie- Rod?
Q5.What is
King Pin Inclined?
Q6.What is
the function of a Braking System?
Q7.What is
the basic principle of air braking system?
Q8.What are
power Brakes?
Q9.What do
you mean by Servo Brake?
Q10.
What is a Cell?
Q11.
What is a Battery?
Q12.
How Many cells are there in a 12Volt battery?
Q13.
What is capacity of a Battery?
Q14.
What is an Electrolyte?
Q15.
What is the source of electrical energy in Automobile?
Q16. What is pre-ignition?
AME 5TH SEM ASSIGNMENT 3RD
AME 5TH SEM ASSIGNMENT 3RD
Submit all assignment 1,2 and 3. Put assignments in a plastic file folder.
Date of Submission: 01-11-2012
Submit all assignment 1,2 and 3. Put assignments in a plastic file folder.
Date of Submission: 01-11-2012
Submit all assignment 1,2 and 3. Put assignments in a plastic file folder.
Date of Submission: 01-11-2012
Q1.
What is fundamental deviation?
Q2.
What is ductile material? Give its
example.
Q3.
What is the effect of keyway and how
this is taken care off in design of the shaft?
Q4.
Which
of the theories of elastic failure is used in design of shafts and why?
Q5.
Write
manufacturing methods of cotter and knuckle joint?
Q6.
What
are applications of coarse and fine threads?
Q7.
What
is caulking and fullering? Differentiate between the two?
Q8.
Sketch
parallel and transverse welds?
Q9.
What
do you understand by self-locking screw? Write its condition?
Q10. Explain
woodruff key? What are its applications?
Q11. What
is factor of safety?
Q12. What
is preloading of bolts?
Q13.
What is function of key? Sketch two
types of keys
Q14.
What are design failure theories?
Q15.
What are different types of shaft?
Q16.
What is spindle?
Q17.
What is the function of cotter joint?
Q18.
Distinguish between knuckle and cotter
joints?
Q19.
Muff coupling is also known as
______________ coupling. (Box)
Q20.
Two shafts are connected by ___________.
(Coupling)
Q21.
________ Coupling is used when two
shafts are intersect at an angle. (Universal)
Q22.
The sleeve and muff coupling is designed
as ____________. (Hollow Cylinder)
Q23.
Oldham coupling is used to connect two
shafts are at __________. (Lateral misalignment)
Q24.
Flange coupling is the standard form of
coupling hardly used in workshops to join two shafts by means of two
_____________. (Flanges)
Q25.
Couplings are mainly divided into two
categories ________ and _______. (Rigid, Flexible)
Q26.
In solid flange coupling _________ is not
used. (Key)
Q27.
What is function of coupling?
Q28.
What is the difference between clutch
and coupling?
Q29. What
are applications of flexible coupling?
Q30. Define a bolt.Submit all assignment 1,2 and 3. Put assignments in a plastic file folder.
Date of Submission: 01-11-2012
Subscribe to:
Posts (Atom)